ISUTAMI BEARINGS
en
FS Series Ball Joint
E-catalog
ISUTAMI BEARINGS

FS Series Ball Joint

FS Series Ball Joint
ISUTAMI ball joint is installed between the ball head and the connecting rod body to realize the mechanical connection between the ball head and the connecting rod body and the transmission of power. The driving force of the ball head part can drive the connecting rod part to move through the ball head connecting rod.An important part of the connector is the pull rod of the ball head housing and the ball head of the steering shaft in the housing. The ball head is hinged with the edge of the axle hole of the ball head housing through the ball head seat at the front of the housing. The ball head seat and the steering spindle are embedded in the hole surface groove of the ball head housing, which can reduce the wear of the ball head and improve the tensile strength of the spindle.
FS Series Ball Joint
ISUTAMI ball joint is installed between the ball head and the connecting rod body to realize the mechanical connection between the ball head and the connecting rod body and the transmission of power. The driving force of the ball head part can drive the connecting rod part to move through the ball head connecting rod.An important part of the connector is the pull rod of the ball head housing and the ball head of the steering shaft in the housing. The ball head is hinged with the edge of the axle hole of the ball head housing through the ball head seat at the front of the housing. The ball head seat and the steering spindle are embedded in the hole surface groove of the ball head housing, which can reduce the wear of the ball head and improve the tensile strength of the spindle.

FS Series Ball Joint Size Chart

Ball Joint FS Series

Part NO Dimensions(mm) Min Pull Test(lb) Min Shear(lb)
d1 d2 d3 L1 L2 L3 L4 L5 S h J
FS185 10-32-2B 10-32-2A 0.438 0.438 0.469 0.438 0.969 1.219 0.375 0.125 0.375 1000 500
FS250 1/4-28-2B 1/4-28-2A 0.438 0.563 0.469 0.500 0.969 1.219 0.375 0.125 0.375 1000 700
FS312 5/16-24-2B 5/16-24-2A 0.500 0.688 0.531 0.563 1.125 1.406 0.438 0.156 0.438 1575 900
FS375 3/8-24-2B 3/8-24-2A 0.625 0.675 0.688 0.750 1.375 1.688 0.500 0.188 0.500 1700 1700
FS500 1/2-20-2B 1/2-20-2A 0.750 1.125 0.875 1.000 1.938 2.375 0.625 0.250 0.625 1900 2700



FS Series Ball Joint Features

Ball joint has been widely used.Due to the implementation of metering, self-regulation of the flow of consciousness greatly enhanced, coupled with the daily use in a large amount of change, so that the amount of the system has a great range of change.If the flow is too small, it may cause the local teng of the group, and then make the group damaged.For the group in the system, if the flow is too small, it may also cause the local freezing of the exhaust pipe, thus causing damage to the unit.For the above bypass pipe, the installation of self-type pressure difference control will lead to the empty phenomenon. If the pressure condition is satisfied and no emptying phenomenon occurs, the pressure of the low-build device will exceed its bearing capacity.Self differential pressure control is often the solution.

According to the potential characteristics, the pressure is set at the appropriate position, and the force is set at the appropriate position.In the process of system operation, the differential pressure before and after the differential pressure control can be kept basically constant.Such does not produce the requirement of empty force phenomenon.When the system stops running, the whole stressed probe has a consistent trend, while the differential pressure control tries to maintain the original basic unchanged by reducing the opening until the differential pressure is closed.At this point, the differential pressure with the pipe line separates the back from the front.The pressure line in the front is guaranteed by the set supplementary force device.The rear part is guaranteed by a constant pressure coupled with the differential pressure.
  • TEL:+86-574-6399-8066
  • FAX:+86-574-6399 8025
  • EMAIL: sales@isutami.com
  • ADDRESS:No.500, North 3rd Ring Road West, Cixi, Ningbo, 315300,China