ISUTAMI BEARINGS
en
GEG-ET-2RS Radial Spherical Plain Bearings
E-catalog
ISUTAMI BEARINGS

GEG-ET-2RS Radial Spherical Plain Bearings

GEG-ET-2RS Radial Spherical Plain Bearings
ISUTAMI spherical plain bearing is a spherical sliding bearing, its sliding contact surface is an inner spherical surface and an outer spherical surface, movement can be in any Angle of rotation swing, lubrication and self-lubrication.Joint bearing has the characteristics of large load capacity, impact resistance, corrosion resistance, wear resistance, self-aligning and good lubrication.Radial spherical plain bearings, single slit outer ring, a lubricating oil tank, able to withstand any direction of the smaller Radial load and axial load.
GEG-ET-2RS Radial Spherical Plain Bearings
ISUTAMI spherical plain bearing is a spherical sliding bearing, its sliding contact surface is an inner spherical surface and an outer spherical surface, movement can be in any Angle of rotation swing, lubrication and self-lubrication.Joint bearing has the characteristics of large load capacity, impact resistance, corrosion resistance, wear resistance, self-aligning and good lubrication.Radial spherical plain bearings, single slit outer ring, a lubricating oil tank, able to withstand any direction of the smaller Radial load and axial load.

GEG-ET-2RS Radial Spherical Plain Bearings Size Chart

Radial Spherical Plain Bearings GEG-ET-2RS

Bearing No. Dimensions Basic Load Rating Weight
d D B C dk rs r1s αo Dynamic Static (kg)
min min C(KN) Co(KN)
GEG17ET-2RS 17 35 20 12 29 0.3 0.3 19 42 83 0.083
GEG20ET-2RS 20 42 25 16 35.5 0.3 0.6 17 68 137 0.153
GEG25ET-2RS 25 47 28 18 40.7 0.6 0.6 17 88 176 0.203
GEG30ET-2RS 30 55 32 20 47 0.6 1 17 112 224 0.304
GEG35ET-2RS 35 62 35 22 53 0.6 1 16 140 280 0.408
GEG40ET-2RS 40 68 40 25 60 0.6 1 17 180 360 0.542
GEG45ET-2RS 45 75 43 28 66 0.6 1 15 220 440 0.713
GEG50ET-2RS 50 90 56 36 80 0.6 1 17 345 695 1.14
GEG60ET-2RS 60 105 63 40 92 1 1 17 440 880 2.05
GEG70ET-2RS 70 120 70 45 105 1 1 16 567 1140 3.01
GEG80ET-2RS 80 130 75 50 115 1 1 14 690 1370 3.64
GEG90ET-2RS 90 150 85 55 130 1 1 15 858 1730 5.22
GEG100ET-2RS 100 160 85 55 140 1 1 14 924 1860 6.05
GEG110ET-2RS 110 180 100 70 160 1 1 12 1340 2700 9.68

GEG-ET-2RS Radial Spherical Plain Bearings Features

The heat treatment temperature of spherical plain bearing parts is not too high, the heating time is not too long, the heating temperature should not be too high, the heating time should be appropriate.Stainless steel or flange parts when exposed to overheating, easy to occur orange peel appearance.If processing is interrupted, the machine should be covered with oil-paper plastic film or roughly similar materials.Then there is the lubricant for the modified bearing.The forging heating temperature and heating time of the stainless steel box and flange parts are strictly controlled to avoid the parts from overheating and the lack of coarse grains.After these steps can be the maintenance of the bearing, so that its use time greatly increased, saving operating costs.After removing the old machine, the bearings using the oil lubricant should be refilled with novel oil and allow the machine to rotate at a low speed for a few minutes.In a period of time, the replacement of the bearing is far more economical than the loss of the sudden stop selected because of the damage.As much as possible to make the oil gather residual contaminants and then drain the oil.For the overheating group, it is considered appropriate to use modified forging to refine the grain method to eliminate the defect, so as to avoid the orange peel-like appearance defect in the cold deformation of the parts and improve the appearance quality of the parts.Check the lubricants on the bearings to make sure they are not exposed to contaminants or moisture.Bearing production, the final temperature is high, but also easy to show the lack of coarse crystal group, should make the forging than appropriate, sufficient, moderate final forging temperature.A small mirror and similar probe are used to inspect the bearing track surface, maintainer and bead.
  • TEL:+86-574-6399-8066
  • FAX:+86-574-6399 8025
  • EMAIL: sales@isutami.com
  • ADDRESS:No.500, North 3rd Ring Road West, Cixi, Ningbo, 315300,China