ISUTAMI BEARINGS
en
SARPP Series Pillow Block Mounted Units Pressed Steel
E-catalog
ISUTAMI BEARINGS

SARPP Series Pillow Block Mounted Units Pressed Steel

SARPP Series Pillow Block Mounted Units Pressed Steel
Features two piece zinc-plated snap-together design with rubber cushion

SARPP Rubber Cushioned Pressed Steel PIllow Block
Eccentric Collar Rubber Cushion Pressed Steel Pillow Block
Light Duty
Narrow Inner Ring
Eccentric Collar Lock
Bore Sizes: 1/2 inch up to 1-1/4 inches

ISUTAMI SARPP pressed steel pillow block mounted unit, also known as ISUTAMI SARPP 2-bolt pressed steel housing mounted bearing unit, is the same as cast iron type, has a stand-up structure, SA is the code name of the bearing housing, R means rubber cushion, and the PP indicates that the bearing is a PP200ST series ball bearing. The bearing is mainly combined of a pressed steel housing and an insert spherical ball bearing. And the housing is made of two pieces of steel plates of snap together design. This zinc-plated stamped steel housing has anti-corrosion function. The spherical bearing is made of bearing steel and also has a certain anti-corrosion function. A dust seal is on each side of the bearing to prevent dust.

The SARPP 2-bolt pressed steel housing mounted bearing unit is light duty. And the inner ring of the insert bearing is narrow and eccentric collar locking type. The diameter of the mounting shaft is 20 mm to 1-1/4 inches. The total length of the unit (a) ranges from 109 mm to 146 mm, the length between two mounting bolt holes (e) at the bottom ranges from 86 mm to 108 mm, and the bottom width of the housing (b) ranges from 29 mm to 33 mm. The total width (Bi) of the unit ranges from 31 mm to 38.9 mm, the height of the shaft (h) center ranges from 28.58 mm to 39.69 mm, and the bolt diameter ranges from 5/16 to 3/8 inch. The overall unit weight ranges from 0.3 kg to 0.7 kg.

ISUTAMI pressed steel pillow block mounted unit is lighter in weight and smaller in size than the cast iron type. It is the smallest stand-up type, but can only be used in applications with low load. Designed for simple applications where load and speed are limited, the SARPP unit provides a simple and effective bearing arrangement that accommodates moderate misalignment of mounting errors and is easy to install on the associated equipment. In addition, there is a rubber cushion between the inserted bearing and the housing, which can reduce the vibration and noise of the bearing device during operation, can also effectively reduce the static electricity generation, and increase the fit between the bearing and the casing. ISUTAMI is able to design and manufacture more sizes of pressed steel pillow block mounted bearing units for different customers.

SARPP Series Pillow Block Mounted Units Pressed Steel
Features two piece zinc-plated snap-together design with rubber cushion

SARPP Rubber Cushioned Pressed Steel PIllow Block
Eccentric Collar Rubber Cushion Pressed Steel Pillow Block
Light Duty
Narrow Inner Ring
Eccentric Collar Lock
Bore Sizes: 1/2 inch up to 1-1/4 inches

ISUTAMI SARPP pressed steel pillow block mounted unit, also known as ISUTAMI SARPP 2-bolt pressed steel housing mounted bearing unit, is the same as cast iron type, has a stand-up structure, SA is the code name of the bearing housing, R means rubber cushion, and the PP indicates that the bearing is a PP200ST series ball bearing. The bearing is mainly combined of a pressed steel housing and an insert spherical ball bearing. And the housing is made of two pieces of steel plates of snap together design. This zinc-plated stamped steel housing has anti-corrosion function. The spherical bearing is made of bearing steel and also has a certain anti-corrosion function. A dust seal is on each side of the bearing to prevent dust.

The SARPP 2-bolt pressed steel housing mounted bearing unit is light duty. And the inner ring of the insert bearing is narrow and eccentric collar locking type. The diameter of the mounting shaft is 20 mm to 1-1/4 inches. The total length of the unit (a) ranges from 109 mm to 146 mm, the length between two mounting bolt holes (e) at the bottom ranges from 86 mm to 108 mm, and the bottom width of the housing (b) ranges from 29 mm to 33 mm. The total width (Bi) of the unit ranges from 31 mm to 38.9 mm, the height of the shaft (h) center ranges from 28.58 mm to 39.69 mm, and the bolt diameter ranges from 5/16 to 3/8 inch. The overall unit weight ranges from 0.3 kg to 0.7 kg.

ISUTAMI pressed steel pillow block mounted unit is lighter in weight and smaller in size than the cast iron type. It is the smallest stand-up type, but can only be used in applications with low load. Designed for simple applications where load and speed are limited, the SARPP unit provides a simple and effective bearing arrangement that accommodates moderate misalignment of mounting errors and is easy to install on the associated equipment. In addition, there is a rubber cushion between the inserted bearing and the housing, which can reduce the vibration and noise of the bearing device during operation, can also effectively reduce the static electricity generation, and increase the fit between the bearing and the casing. ISUTAMI is able to design and manufacture more sizes of pressed steel pillow block mounted bearing units for different customers.

SARPP Series Pillow Block Mounted Units Pressed Steel Size Chart

Pillow Block Mounted Units Pressed Steel SARPP

Bearing No.
Insert
Bearing No.
Housing No. Rubber No. Shaft Dia Boundary Dimensions(mm) Bolt Size
Mass
(Kg)
in. mm h a e b S1 S2 g w Bi n W
SARPP206-20 SA206-20 PP207ST R-7 1-1/4 - 39.69 146 108 33 13 19 6 79 38.9 8 44.5 43167 0.7
SARPP206-17 SA206-17 PP207ST R-7 1-1/16 - 39.69 146 108 33 13 19 6 79 38.9 8 44.5 43167 0.7
SARPP206-18 SA206-18 PP207ST R-7 1-1/8 - 39.69 146 108 33 13 19 6 79 38.9 8 44.5 43167 0.7
SARPP206-19 SA206-19 PP207ST R-7 1-3/16 - 39.69 146 108 33 13 19 6 79 38.9 8 44.5 43167 0.7
SARPP205-15 SA205-15 PP206ST R-6 15/16 - 33.34 124 95 32 10 14 6 67 35.7 7.5 38.1 43167 0.5
SARPP205-16 SA205-16 PP206ST R-6 1 - 33.34 124 95 32 10 14 6 67 35.7 7.5 38.1 43167 0.5
SARPP206 SA206 PP207ST R-7 - 30 39.69 146 108 33 13 19 6 79 38.9 8 44.5 M10 0.7
SARPP204-12 SA204-12 PP205ST R-5 3/4 - 28.58 109 86 29 10 14 5 56 31 7 32 43167 0.3
SARPP205 SA205 PP206ST R-6 - 25 33.34 124 95 32 10 14 6 67 35.7 7.5 38.1 M10 0.5
SARPP205-14 SA205-14 PP206ST R-6 7/8 - 33.34 124 95 32 10 14 6 67 35.7 7.5 38.1 43167 0.5
SARPP201-8 SA201-8 PP204ST R-4 1/2 - 25.4 105 76 25 10 13 4 53 31 6 28.6 43236 0.2
SARPP202-10 SA202-10 PP204ST R-4 5/8 - 25.4 105 76 25 10 13 4 53 31 6 28.6 43236 0.2
SARPP204 SA204 PP205ST R-5 - 20 28.58 109 86 29 10 14 5 56 31 7 32 M10 0.3
  • TEL:+86-574-6399-8066
  • FAX:+86-574-6399 8025
  • EMAIL: sales@isutami.com
  • ADDRESS:No.500, North 3rd Ring Road West, Cixi, Ningbo, 315300, China