ISUTAMI BEARINGS
en
SUCC200 Stainless Steel Mounted Bearings
E-catalog
ISUTAMI BEARINGS

SUCC200 Stainless Steel Mounted Bearings

SUCC200 Stainless Steel Mounted Bearings
ISUTAMI stainless steel mounted bearings due to the size of the diameter of axle and bearing hole mating surface roughness, do not meet the standard requirements to cause excessive interference fit, the bearing race is being squeezed from a large, resulting in the radial clearance of bearing itself is reduced, the bearing rotating difficulties, fever, wear or jammed, caused serious bearing inner and outer race in cracking during installation.The non-rotating seat ring is usually fitted with a small clearance or interference, so that the non-rotating seat ring may have a small creep, and the contact surface between the seat ring and the rolling body is constantly replaced, and the seat ring raceway wear is uniform.At the same time, it can also eliminate the phenomenon that the rolling body in the bearing is stuck in the axial direction due to the thermal elongation of the shaft.However, excessive clearance coordination will make the non-rotating seat ring rotate together with the rolling body, resulting in serious wear and tear between the shaft and the inner seat ring, and friction will make the bearing hot and vibration.
SUCC200 Stainless Steel Mounted Bearings
ISUTAMI stainless steel mounted bearings due to the size of the diameter of axle and bearing hole mating surface roughness, do not meet the standard requirements to cause excessive interference fit, the bearing race is being squeezed from a large, resulting in the radial clearance of bearing itself is reduced, the bearing rotating difficulties, fever, wear or jammed, caused serious bearing inner and outer race in cracking during installation.The non-rotating seat ring is usually fitted with a small clearance or interference, so that the non-rotating seat ring may have a small creep, and the contact surface between the seat ring and the rolling body is constantly replaced, and the seat ring raceway wear is uniform.At the same time, it can also eliminate the phenomenon that the rolling body in the bearing is stuck in the axial direction due to the thermal elongation of the shaft.However, excessive clearance coordination will make the non-rotating seat ring rotate together with the rolling body, resulting in serious wear and tear between the shaft and the inner seat ring, and friction will make the bearing hot and vibration.

SUCC200 Stainless Steel Mounted Bearings Products

SUCC200 Stainless Steel Mounted Bearings Size Chart

Stainless Steel Mounted Bearings SUCC200

Bearing No.
Insert
Bearing No.
Housing No. Shaft Dia
Mass
(Kg)
in. mm a L B s
SUCC201 SUC201 SC203 - 12 72 20 21.0 12.7 0.51
SUCC201-8 SUC201-8 1/2 -
SUCC202 SUC202 - 15
SUCC202-10 SUC202-10 5/8 -
SUCC203 SUC203 - 17
SUCC203-11 SUC203-11 11/16 -
SUCC204 SUC204 SC204 - 20 72 20 31.0 12.7 0.49
SUCC204-12 SUC204-12 3/4 -
SUCC205 SUC205 SC205 - 25 80 22 34.1 14.3 0.69
SUCC205-14 SUC205-14 7/8 -
SUCC205-15 SUC205-15 15/16 -
SUCC205-16 SUC205-16 1 -
SUCC206 SUC206 SC206 - 30 85 27 38.1 15.9 0.88
SUCC206-17 SUC206-17 1-1/16 -
SUCC206-18 SUC206-18 1-1/8 -
SUCC206-19 SUC206-19 1-3/16 -
SUCC206-20 SUC206-20 1-1/4 -
SUCC207 SUC207 SC207 - 35 90 28 42.9 17.5 0.97
SUCC207-20 SUC207-20 1-1/4 -
SUCC207-21 SUC207-21 1-5/16 -
SUCC207-22 SUC207-22 1-3/8 -
SUCC207-23 SUC207-23 1-7/16 -
SUCC208 SUC208 SC208 - 40 100 30 49.2 19.0 1.28
SUCC208-24 SUC208-24 1-1/2 -
SUCC208-25 SUC208-25 1-9/16 -
SUCC209 SUC209 SC209 - 45 110 31 49.2 19.0 1.79
SUCC209-26 SUC209-26 1-5/8 -
SUCC209-27 SUC209-27 1-11/16 -
SUCC209-28 SUC209-28 1-3/4 -
SUCC210 SUC210 SC210 - 50 120 33 51.6 19.0 1.98
SUCC210-29 SUC210-29 1-13/16 -
SUCC210-30 SUC210-30 1-7/8 -
SUCC210-31 SUC210-31 1-15/16 -
SUCC210-32 SUC210-32 2 -

SUCC200 Stainless Steel Mounted Bearings Features

Stainless steel mounted bearings surface strain found cutting abrasive, abrasive ingredients for non-ferrous metal.In the condition of liquid lubrication, the surface is separated by lubricating oil without direct contact, can also greatly reduce the friction loss and surface wear, oil film also has a certain capacity of vibration absorption.Stainless steel mounted bearings produce peak of the metamorphic layer, and is easy to wear, but also left by grinding metamorphic layers can be removed.The service life of the workpiece is increased by about 5 times.Stainless steel mounted bearings for superfinishing artifacts, after the general assembly can reduce the running noise 8 ~ 10 db, and small vibration.Smooth operation.The allowance is an order of magnitude less than the grinding allowance and is actually only a few microns.For low pressure feed machining.Therefore, the size dispersion of superfinishing is very small and the qualified rate is very high.Bearing surface for the cross mesh, easy to store oil, will not appear when grinding easy wear, easy to heat and burning phenomenon.Stainless steel bearings have complex trajectories, and can be cut from the role of transition to grinding, can quickly reduce the surface roughness.But because it has the vibration which changes the motion direction repeatedly, the influence its further enhances the processing surface quality.
  • TEL:+86-574-6399-8066
  • FAX:+86-574-6399 8025
  • EMAIL: sales@isutami.com
  • ADDRESS:No.500, North 3rd Ring Road West, Cixi, Ningbo, 315300, China