ISUTAMI BEARINGS
en
Operation of the rod joint bearing
ISUTAMI BEARINGS

Operation of the rod joint bearing


1. In the absence or inability to use the press, the end rod joint bearing can be installed with the assembly sleeve and the small hammer. The hammering force should be transmitted evenly to the entire circumference of the end face of the end rod joint bearing ring, so the hammered end face of the assembly casing should be made spherical.

2. The force required to install the end rod joint bearing is related to the size of the joint bearing and the amount of interference. For medium or large joint bearings with large interference, the method is hot. Before hot loading, put the end rod joint bearing or the separable joint bearing ring into the fuel tank or special heater and heat evenly to 80-100 °C, not more than 100 °C.

3. Hot-fit joint bearings require skilled operation skills. When the joint bearing is removed from the heating tank or heater, immediately wipe off the oil and attachments on the surface of the joint bearing with a clean cloth (note that cotton yarn cannot be used), and then put it in front of the mating surface, in one operation. The joint bearing is pushed to the position against the shoulder. Always tighten during the cooling process or tap the joint bearing with a small hammer through the fitting sleeve to make it tight. When installing the end rod joint bearing, the joint bearing should be slightly rotated to avoid the installation from tipping or jamming.

4. When the outer ring of the end rod joint bearing and the housing hole are tightly fitted, the housing can be heated and then loaded into the joint bearing. In particular, the joint bearing of light metal material may cause damage to the mating surface due to the pressing of the outer ring during the tight fitting process. In this case, the end rod joint bearing should be heated first.

There are several types of rod end joint bearing repairs.

Regular maintenance: In order to ensure the normal operation of the host, according to the request of the host and the design theory and application experience of the bearing, set a maintenance cycle and regular maintenance.

Fault repair: stop inspection and maintenance when the bearing is in trouble.

Early warning maintenance: Apply advanced bearing fault diagnosis technology, stop real-time monitoring of the bearing operation status, and make advance notice before the bearing attack, stop maintenance.

During the operation of the bearing, there must be phenomena such as sound, temperature and vibration. Therefore, regarding the maintenance and maintenance of the bearing in operation, it is possible to find the abnormal change of the bearing through the methods of listening, touching, observing, and using a bearing fault diagnosis instrument, and to determine whether the rod end joint bearing can be in a normal working state according to the changed state.
Related News
  • How to protect your bearing investment

    How to protect your bearing investment

    October 6, 2019Inspection and maintenance are important to maintain performance, extend service life, avoid downtime, and promote total cost of ownership.Bearing inspection and maintenance are important not only to ...view
  • Bearing Overheating

    Bearing Overheating

    April 21, 2019By Team BCOverheating is a major indicator, along with vibration and noise, of an underlying problem affecting a bearing or related components. Because normal operating temperature varies widely from ...view
  • Linear bearing solutions for machine tool applications

    Linear bearing solutions for machine tool applications

    June 30, 2019The machine tool occupies a very important position in the machinery industry. As one of the basic production equipment, the machine tool has good quality and high processing efficiency, which is dire...view
  • Bearings vs bushings in 3D printing

    Bearings vs bushings in 3D printing

    April 3, 2019Edited by Mike SantoraA small but vocal discussion in the 3D printer community is on bearings and bushings that are used by 3D printers, and how these can be optimized to create better printers and be...view
  • The difference between linear guide bearings and linear guides

    The difference between linear guide bearings and linear guides

    August 3, 2019Linear guide bearings are a common name for some people. They generally refer to linear optical axes (including various flanged linear bearing blocks), linear guide optical axes, and linear circular g...view
  • Selecting shafts for linear bearings: two things you need to know

    Selecting shafts for linear bearings: two things you need to know

    April 14, 2019BY DANIELLE COLLINSIn a round shaft linear bearing system, the shaft acts as the inner raceway of the bearing and plays a significant role in the wear and life of the system.Both recirculating and pla...view
  • TEL:+86-574-6399-8066
  • FAX:+86-574-6399 8025
  • EMAIL: sales@isutami.com
  • ADDRESS:No.500, North 3rd Ring Road West, Cixi, Ningbo, 315300, China